-
Sand Blaster Machine Accessories Pneumatic Control Switch Pneumatic Remote Control Handle Sand Blasting 1 piece
The new pneumatic switch of sandblasting machine changes the traditional finger pressing to palm pressing, so as to reduce the labor intensity.
Specification:
Material: aluminum alloy
Working pressure: 0.4 ~ 0.8MPa
Air inlet: 8mm
Air outlet: 8mm
Size: 235 * 40 * 50mm
Trachea connector: 1 / 8
-
HOLDWIN Black plastic O rings for sandblaster cabinet sandblast machine parts
Recycling Conveyor Sand Blasting Machine
Whether you’re building your own cabinet, or upgrading, this kit is a must!
Screw this ring to the front of your cabinet, and attach glove.When installed, it can easily hold gloves in place. -
high pressure 1 1/4” fine thread B4C carbide Venturi sandblasting nozzle with yellow nylon nozzle holder
Boron carbide nozzles offer the longest wear life of any standard nozzle material.
Peak nozzle production performance is maintained for longer periods with optimum consumption of air and abrasive.
Boron carbide nozzles typically outwear tungsten carbide nozzles by five to ten times and silicon carbide by two to three times.
Boron carbide nozzles are recommended for use with abrasives such as aluminum oxide and aggressive mineral aggregates.
Our selection of nozzles is unmatched, anywhere
We have standard products that can replace the original nozzles installed on most equipment.
We also have higher performance upgrades for most OEM products to allow you to achieve optimum blasting effectiveness,efficiency and reduce your total costs.
Approximate Nozzle Service Life in Hours *
-
HOLDWIN Sandblaster Tube Connector Yellow Nylon Quick Connector Hose Coupling Blasting Hose
Sandblasting couplings are designed to connect hoses with sandblasting nozzles. The sandblasting couplings comprise claw couplings with claw (lug) distance or 58 mm and couplings – nozzle holders with NPT female thread or 50 mm coarse UNC thread. To assemble, the hose must be inserted inside the ferrule of the coupling and secured by screwing it down to the ferrule. The claw couplings are equipped with NBR rubber seals. The claw couplings are made of nylon (polyamide). Nozzle holders are made of nylon. The claw couplings must be secured with a pin after they are coupled. Working pressure 12 bar.
-
Rubber sandblasting hose 1” 1 1/4” Sandblaster Machine parts
Tube: black antistatic abrasion resistant nature rubber compound
Reinforcement: by Nylon cord ply
Cover: black abrasion and antistatic rubber.
Applications: for industrial cleaning, cutting, polishing, casting serving services.
Temperature: -40°C + 80°C
Packing: trans. P.V.C. film -
Holdwin Sandblast boron cabide nozzle
100% brand new and high quality
Features:Low density, high hardness and strength corrosion.Low thermal conductivity. Super duarable. -
Shot blasting nozzle/sandblasting nozzles/Tungsten carbide nozzle
- 【Wide range of applications】:Specially used for polishing and spraying various dead ends, rough edges and rusty details of metal, as well as shipbuilding, large workpieces of oil and rust removal, steel structures, mining equipment, etc.
- 【Sandblasting gun material】: sandblasting gun is made of aluminum alloy, good quality, high wear resistance, internal material made of boron carbide, long service life, make your work more efficient and convenient.
- 【Support a variety of sandblasting materials】: Suitable for (8-500#) metal and non-metal sandblasting materials, steel sand, steel grit, copper sand, baking soda or glass beads, sodium bicarbonate, silica, walnut, garnet, etc. Please make sure to use the correct abrasive for your project.
- 【Features】:Simple to operate, suitable for surface treatment with various large industrial equipment, high intensity of injection pressure, with to suitable open sand blasting machine, rust removal efficiency up to 25-30 square meters per hour.
- 【Note】:While using the sandblasting gun, you must wear protective equipment and operate it safely and carefully, please do not point the gun at people or animals.
-
HOLDWIN Nylon Sandblasting hose couplings for Sandblast pot hose blast hose connector sandblaster parts
Operation method:
1. Two tubes of the same length: Take out two joints of the same size, align the bayonet, press in and rotate to catch, then connect the sandblasting tube at both ends.
2. Two tubes of different lengths: Take out two joints of corresponding size, align the bayonet, press it to rotate, and then connect the sandblasting tube at both ends.
3. Sandblasting tank joint: Connect our short joint directly to the bottom of the sandblasting machine.
Benefits:Simple operation, quick connection with sandblasting tube, improved work efficiency, less unnecessary trouble, better fixability. -
Sandblaster Parts Nylon quick couplings for sandblasting hose
Quick Nylon couplings for sandblast hose sandblast nozzle holder for sandblasting machine
There are 4 different size as following :
Q-IM-NY to fit OD34mm hose
Q-1-NY to fit OD39mm hose
Q-2-NY to fit OD50mm hose
Q-3-NY to fit OD55mm hose
SB-NY with fine thread 45mm
When the blast tube is not long enough, we can connect the two tubes with our quick coupling.
Operation method:
1. Two tubes of the same length: Take out two joints of the same size, align the bayonetpress in and rotate to catch, then connect the sandblasting tube at both ends.
2. Two tubes of different lengths: Take out two joints of corresponding size, align the bayonetpress it to rotate, and then connect the sandblasting tube at both ends.
3. Sandblasting tank joint: Connect our short joint directly to the bottom of the sandblasting machine.
Benefits: Simple operation, quick connection with sandblasting tube, improved work efficiency less unnecessary trouble, better fixability.
Occasion: Suitable for shipbuilding, large workpiece degreasing, steel structure, large castings, large molds, mechanical casings containers valves mining equipment, etc. -
High pressure sand blasting hose
Tube: black antistatic abrasion resistant nature rubber compound
Reinforcement: by Nylon cord ply
Cover: black abrasion and antistatic rubber.
Applications: for industrial cleaning, cutting, polishing, casting serving services.
Temperature: -40°C + 80°C
Packing: trans. P.V.C. film -
Cylindrical Ceramic Blasting Nozzles
About this Ceramic nozzles
- Durable ceramic sandblast nozzle for injection of medium particles for rapid removal of paint, rust, corrosion and scale.
- Mainly used for deep processing such as sandblasting and engraving of glass. Carving and processing of marble and other stones.
- Suitable for sandblasting and derusting the surface of industrial machinery parts and castings such as machinery and metallurgical casting.
- Can use a variety of sandblasted media such as glass beads, brown corundum, garnet, soda water, walnut shell.
- Packing specification: ceramic nozzle*10.
-
sell well double venturi boron sandblast nozzle for you
Appearance: carbon steel shell after sand blasting and plating, aluminum shell after sand blasting.